Aruba 203H — точка доступа, которую возможно разместить на стене или на столе, и запитать непосредственно от коммутатора по PoE.

Официальная спецификация:

• AP-203H SERIES SPECIFICATIONS
  Unified flexible radio 802.11ac 2×2:2SS hospitality and branch AP with internal antennas Supports wall-box and desk mount deployments

  WI-FI RADIO SPECIFICATIONS

  AP type: Indoor, flexible radio: 5GHz 802.11ac 2×2 MIMO OR 2.4GHz 802.11n 2×2 MIMO1, or 5GHz 802.11ac 1×1 AND 2.4GHz 802.11n 1×11 Software-configurable radio supports 5GHz (Radio 0) and/or 2.4GHz (Radio 1) 5GHz: Two spatial stream Single User (SU) MIMO for up to 867Mbps wireless data rate to individual 2×2 VHT80 client devices 2.4GHz: Two spatial stream Single User (SU) MIMO for up to 400Mbps wireless data rate to individual 2×2 VHT40 client devices (300Mbps for HT40 802.11n client devices) Support for up to 32 associated client devices per radio, and up to 8 BSSIDs per radio Supported frequency bands (country-specific restrictions apply): 2.400 to 2.4835GHz 5.150 to 5.250GHz 5.250 to 5.350GHz 5.470 to 5.725GHz 5.725 to 5.850GHz Available channels: Dependent on configured regulatory domain Dynamic frequency selection (DFS) optimizes the use of available RF spectrum Supported radio technologies: 802.11b: Direct-sequence spread-spectrum (DSSS) 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) Supported modulation types: 802.11b: BPSK, QPSK, CCK 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM Transmit power: Configurable in increments of 0.5 dBm Maximum (conducted) transmit power (limited by local regulatory requirements): 2.4GHz band: +18 dBm per chain, +21 dBm aggregate (2×2 mode) 5GHz band: +16 dBm per chain, +19 dBm aggregate (2×2 mode) Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain Maximum ratio combining (MRC) for improved receiver performance Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance Short guard interval for 20MHz, 40MHz and 80MHz channels Space-time block coding (STBC) for increased range and improved reception Low-density parity check (LDPC) for high-efficiency error correction and increased throughput Transmit beam-forming (TxBF) for increased signal reliability and range (2×2 mode) Supported data rates (Mbps): 802.11b: 1, 2, 5.5, 11 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 802.11n: 6.5 to 300 (MCS0 to MCS15) 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2 for VHT20/40/80) 802.11n high-throughput (HT) support: HT 20/40 802.11ac very high throughput (VHT) support: VHT 20/40/80 802.11n/ac packet aggregation: A-MPDU, A-MSDU

  WI-FI ANTENNAS

  Two integrated dual-band moderately directional antennas for 2×2 MIMO with maximum individual antenna gain of 4.9dBi in 2.4GHz and 6.0dBi in 5GHz. Built-in antennas are optimized for vertical orientation of the AP. The horizontal beamwidth is roughly 120 degrees. Combining the patterns of each of the antennas of the MIMO radios (in 2×2 mode), the peak gain of the effective per-antenna pattern is 2.3dBi in 2.4GHz and 3.4dBi in 5GHz.

  OTHER INTERFACES

  Uplink: 10/100/1000BASE-T Ethernet (RJ-45, back) Auto-sensing link speed and MDI/MDX 802.3az Energy Efficient Ethernet (EEE) PoE-PD (input): 48 Vdc (nominal) 802.3af/at PoE Local: 10/100/1000BASE-T Ethernet (RJ-45, bottom) Auto-sensing link speed and MDI/MDX 802.3az Energy Efficient Ethernet (EEE) Passive pass-through interface (two RJ-45, back and bottom) USB host interface (Type A connector) For Aruba LS-BT1USB BLE radio modules only Visual indicators (LEDs): Power/system status Radio status Local network port status Reset/LED control button (“paperclip access”) Factory reset (when activated during device power up) LED control: toggle off/normal Serial console interface (custom, uUSB physical jack)

  ¹ 256-QAM modulation (802.11ac) supported by the 2.4GHz radio as well.

• ENCRYPTED THROUGHPUT
  Maximum IPsec encrypted wired throughput: 20Mbps

  POWER SOURCES AND CONSUMPTION
  The AP is powered through Power over Ethernet (PoE) An optional PoE power injector is sold separately Power over Ethernet (PoE): 48 Vdc (nominal) 802.3af/802.3at compliant source Maximum (worst-case) power consumption: 7.4W. Includes up to 100mW for an attached USB BLE module Maximum (worst-case) power consumption in idle mode: 3.9W.

  MOUNTING
  The AP ships with a mounting plate to attach the AP to a single-gang wall-box (most international variations covered). The AP securely attaches to the plate; a custom security tool to remove the AP from the plate ships with the product. Several optional mount kits are available to attach the AP to a dual-gang wall-box, directly to the wall, or to support desk mounting.

  MECHANICAL
  Dimensions/weight (unit,including single-gang wall box mount plate): 86mm (W) x 26.5mm (D) x 140mm (H) 225g Dimensions/weight (shipping): 115mm (W) x 47mm (D) x 165mm (H) 290g

  ENVIRONMENTAL
  Operating: Temperature: 0° C to +40° C (+32° F to +104° F) Humidity: 5% to 93% non-condensing Storage and transportation: Temperature: -40° C to +70° C (-40° F to +158° F)

  REGULATORY
  FCC/Industry of Canada CE Marked R&TTE Directive 1995/5/EC Low Voltage Directive 72/23/EEC EN 300 328 EN 301 489 EN 301 893 UL/IEC/EN 60950 EN 60601-1-1 and EN 60601-1-2 For more country-specific regulatory information and approvals, please see your Aruba representative.

  RELIABILITY
  MTBF: 780,000 hours (89 years) at +25C° operating temperature

  REGULATORY MODEL NUMBER
  AP-203H-xx (all variants): APINH203

  CERTIFICATIONS
  CB Scheme Safety, cTUVus UL2043 plenum rating Wi-Fi Alliance (WFA) certified 802.11a/b/g/n/ac

  WARRANTY
  Aruba limited lifetime warranty

  MINIMUM SOFTWARE VERSION
  ArubaOS™ 6.5.2.0/8.2.0.0 Aruba InstantOS™ 6.5.3.0/8.2.0.0

Технические эксперты подберут оптимальное решение под ваши задачи. Обращайтесь! Телефон: +7-495-514-00-10 E-mail: info@compuway.ru