Aruba 203R - настольная точка доступа

Aruba 203R — настольная точка доступа для удалённых филиалов, небольших гостиниц, домашнего использования.

Отделение этой группы от группы «Точки доступа для помещений (Indoor Access Point)» достаточно условно. Функциональность точек доступа, представленных в группе позволяет подключать их к корпоративным контроллерам, а мощность достаточна для работ с достаточно высокими скоростями до 1000 Мбит в секунду. Строить системы высокой плотности или большие беспроводные сети в одном помещении на таких точках опрометчиво, но если вы хотите централизовано управлять беспроводными сетями в значительном количестве филиалов, небольших складах или у сотрудников работающих из дома — это отличный выбор. Aruba 203R — настольная точка доступа без поддержки работы от PoE.

Официальная спецификация:

RAP-203R SERIES SPECIFICATIONS
Unified flexible radio 802.11ac remote AP with internal antennas. Supports wall-box and desk mount deployments

WI-FI RADIO SPECIFICATIONS
AP type: Indoor, flex radio: 5GHz 802.11ac 2×2 MIMO OR 2.4GHz 802.11n 2×2 MIMO¹, or 5GHz 802.11ac 1×1 AND 2.4GHz 802.11n 1×11 Software-configurable radio supports 5GHz (Radio 0) and/or 2.4GHz (Radio 1) 5GHz: Two spatial stream Single User (SU) MIMO for up to 867Mbps wireless data rate to individual 2×2 VHT80 client devices 2.4GHz: Two spatial stream Single User (SU) MIMO for up to 400Mbps wireless data rate to individual 2×2 VHT40 client devices (300Mbps for HT40 802.11n client devices) Support for up to 256 associated client devices per radio, and up to 16 BSSIDs per radio Supported frequency bands (country-specific restrictions apply): 2.400 to 2.4835GHz 5.150 to 5.250GHz 5.250 to 5.350GHz 5.470 to 5.725GHz 5.725 to 5.850GHz Available channels: Dependent on configured regulatory domain Dynamic frequency selection (DFS) optimizes the use of available RF spectrum Supported radio technologies: 802.11b: Direct-sequence spread-spectrum (DSSS) 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) Supported modulation types: 802.11b: BPSK, QPSK, CCK 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM Transmit power: Configurable in increments of 0.5 dBm Maximum (conducted) transmit power (limited by local regulatory requirements): 2.4GHz band: +18 dBm per chain, +21 dBm aggregate (2×2 mode) 5GHz band: +18 dBm per chain, +21 dBm aggregate (2×2 mode) Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks Maximum ratio combining (MRC) for improved receiver performance Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance Short guard interval for 20MHz, 40MHz and 80MHz channels Space-time block coding (STBC) for increased range and improved reception Low-density parity check (LDPC) for high-efficiency error correction and increased throughput Transmit beam-forming (TxBF) for increased signal reliability and range Supported data rates (Mbps): 802.11b: 1, 2, 5.5, 11 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 802.11n: 6.5 to 300 (MCS0 to MCS15) 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2 for VHT20/40/80) 802.11n high-throughput (HT) support: HT 20/40 802.11ac very high throughput (VHT) support: VHT 20/40/80 802.11n/ac packet aggregation: A-MPDU, A-MSDU

WI-FI RADIO SPECIFICATIONS

AP type: Indoor, flex radio:
- 5GHz 802.11ac 2×2 MIMO OR 2.4GHz 802.11n 2×2 MIMO¹, or
- 5GHz 802.11ac 1×1 AND 2.4GHz 802.11n 1×11
Software-configurable radio supports 5GHz (Radio 0) and/or 2.4GHz (Radio 1)
5GHz: Two spatial stream Single User (SU) MIMO for up to 867Mbps wireless data rate to individual 2×2 VHT80 client devices
2.4GHz: Two spatial stream Single User (SU) MIMO for up to 400Mbps wireless data rate to individual 2×2 VHT40 client devices (300Mbps for HT40 802.11n client devices)
Support for up to 256 associated client devices per radio, and up to 16 BSSIDs per radio
Supported frequency bands (country-specific restrictions apply):
- 2.400 to 2.4835GHz
- 5.150 to 5.250GHz
- 5.250 to 5.350GHz
- 5.470 to 5.725GHz
- 5.725 to 5.850GHz
Available channels: Dependent on configured regulatory domain
Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
Supported modulation types:
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
Transmit power: Configurable in increments of 0.5 dBm
Maximum (conducted) transmit power (limited by local regulatory requirements):
- 2.4GHz band: +18 dBm per chain, +21 dBm aggregate (2×2 mode)
- 5GHz band: +18 dBm per chain, +21 dBm aggregate (2×2 mode)
- Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain
Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks
Maximum ratio combining (MRC) for improved receiver performance
Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
Short guard interval for 20MHz, 40MHz and 80MHz channels
Space-time block coding (STBC) for increased range and improved reception
Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
Transmit beam-forming (TxBF) for increased signal reliability and range
Supported data rates (Mbps):
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 300 (MCS0 to MCS15)
- 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2 for VHT20/40/80)
802.11n high-throughput (HT) support: HT 20/40
802.11ac very high throughput (VHT) support: VHT 20/40/80
802.11n/ac packet aggregation: A-MPDU, A-MSDU

WI-FI ANTENNAS
Two integrated dual-band omni-directional antennas for 2×2 MIMO with maximum individual antenna gain of 0.7dBi in 2.4GHz and 1.0dBi in 5GHz. Built-in antennas are optimized for vertical orientation of the AP. Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the effective per-antenna pattern is -0.4dBi in 2.4GHz and 0.5dBi in 5GHz.

OTHER INTERFACES
Uplink: 10/100/1000BASE-T Ethernet (RJ-45, back) Auto-sensing link speed and MDI/MDX 802.3az Energy Efficient Ethernet (EEE) Local: Two 10/100/1000BASE-T Ethernet (RJ-45, back) Auto-sensing link speed and MDI/MDX 802.3az Energy Efficient Ethernet (EEE) One port (E2): PoE-PSE (output): 48 Vdc (nominal) 802.3af PoE (AP-203RP models) Bluetooth Low Energy (BLE) radio Up to 4dBm transmit power (class 2) and -93dBm receive sensitivity Integrated antenna with moderately directional pattern and peak gain of 1dBi USB 2.0 host interface (Type A connector, top) 3G/4G cellular modems Device battery charging port Capable of supplying up to 1A/5 watts of power to an attached device AC power interface, 2 prong IEC 60320-1 C8 receptacle (back) Visual indicators (LEDs, front): Power/system status Radio status Local network port status (2x) Includes PoE-PSE status (AP-203RP models) Reset/LED control button (“paperclip access”, bottom) Factory reset (when activated during device power up) LED control: toggle off/normal Serial console interface (custom, uUSB physical jack, bottom)

OTHER INTERFACES

Uplink: 10/100/1000BASE-T Ethernet (RJ-45, back)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Efficient Ethernet (EEE)
Local: Two 10/100/1000BASE-T Ethernet (RJ-45, back)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Efficient Ethernet (EEE)
- One port (E2): PoE-PSE (output): 48 Vdc (nominal) 802.3af PoE (AP-203RP models)
Bluetooth Low Energy (BLE) radio
- Up to 4dBm transmit power (class 2) and -93dBm receive sensitivity
- Integrated antenna with moderately directional pattern and peak gain of 1dBi
USB 2.0 host interface (Type A connector, top)
- 3G/4G cellular modems
- Device battery charging port
- Capable of supplying up to 1A/5 watts of power to an attached device
AC power interface, 2 prong IEC 60320-1 C8 receptacle (back)
Visual indicators (LEDs, front):
- Power/system status
- Radio status
- Local network port status (2x)
  - Includes PoE-PSE status (AP-203RP models)
Reset/LED control button (“paperclip access”, bottom)
- Factory reset (when activated during device power up)
- LED control: toggle off/normal
Serial console interface (custom, uUSB physical jack, bottom)

¹ 256-QAM modulation (802.11ac) supported by the 2.4GHz radio as well.

ENCRYPTED THROUGHPUT
Maximum IPsec encrypted wired throughput: 20Mbps

POWER SOURCES AND CONSUMPTION
The AP supports direct AC power: 90V – 265V, 47Hz – 63Hz. Note that the unit does not include an AC power cord (IEC C7 plug). A compatible region-specific cord should be selected and added when ordering the AP. Maximum (worst-case) power consumption: 7.5W. Excludes power consumed by external USB and/or PoE-PD device (and internal losses); this could add up to 6W for a 5W/1A USB device and up to 18W for a max load (15.4W) 802.3af PoE-PD device Maximum (worst-case) power consumption in idle mode: 4.6W.

POWER SOURCES AND CONSUMPTION

The AP supports direct AC power: 90V – 265V, 47Hz – 63Hz.
- Note that the unit does not include an AC power cord (IEC C7 plug). A compatible region-specific cord should be selected and added when ordering the AP.
Maximum (worst-case) power consumption: 7.5W.
- Excludes power consumed by external USB and/or PoE-PD device (and internal losses); this could add up to 6W for a 5W/1A USB device and up to 18W for a max load (15.4W) 802.3af PoE-PD device
Maximum (worst-case) power consumption in idle mode: 4.6W.

MOUNTING
The AP supports desk mount without additional accessories. A cover ships with the AP to hide connectors, cables and product labels. The cover can be used to support wall mounted deployments as well.

MECHANICAL
Dimensions/weight (unit, with cable cover): 155mm (W) x 50mm (D) x 95mm (H) 320g (AP-203R), 340g (AP-203RP) Dimensions/weight (shipping): 224mm (W) x 159mm (D) x 78mm (H) 510g (AP-203R), 590g (AP-203RP)

ENVIRONMENTAL
Operating: Temperature: 0° C to +40° C (+32° F to +104° F) Humidity: 5% to 93% non-condensing Storage and transportation: Temperature: -40° C to +70° C (-40° F to +158° F)

REGULATORY
FCC/Industry of Canada CE Marked R&TTE Directive 1995/5/EC Low Voltage Directive 72/23/EEC EN 300 328 EN 301 489 EN 301 893 UL/IEC/EN 60950 EN 60601-1-1 and EN 60601-1-2

RELIABILITY
MTBF at +25C° operating temperature: AP-203R: 324,000 hours (37 years) AP-203RP: 308,000 hours (35 years)

REGULATORY MODEL NUMBER
AP-203R-xx (all variants): APINR203 AP-203RP-xx (all variants): APINP203

CERTIFICATIONS
CB Scheme Safety, cTUVus Wi-Fi Alliance (WFA) certified 802.11a/b/g/n/ac

MINIMUM SOFTWARE VERSION
ArubaOS™ 6.5.2.0/8.2.0.0 Aruba InstantOS™ 6.5.2.0/8.2.0.0

Технические эксперты подберут оптимальное решение под ваши задачи. Обращайтесь! Телефон: +7-495-514-00-10 E-mail: info@compuway.ru

Aruba 203R Series